MARINE EQUIPMENT DEC 2020

Marine equipment

Ballast Water Management Systems

The SKF BlueSonic Ballast Water Management System is ideally suited for retrofits where space is at a premium
The SKF BlueSonic Ballast Water Management System complies with both the IMO and USCG regulations (IMO type approval has been granted and USCG certification is expected shortly).
BlueSonic uses a combination of UV and ultrasonic treatment in order to keep the UV light clean and efficient without the crew having to stop the equipment in order to chemically the UV lamps. In common with most UV systems BlueSonic is targeted at systems with flow rates of less than 1,500 m3/hr.
Being of modular design with a small foot-print, BlueSonic is ideally suited for retrofits where space is at a premium.
Each module is rated for 250 m3/h. The modules are installed in parallel in order to provide for throughput of 500 m3/h, 750 m3/h, 1000 m3/h and more. If fitted with the optional isolation valve, it is possible to isolate any one of the units in order to carry out maintenance work, whilst the system continues to operate, albeit at a reduced rate.
A backflushing filter with 20 micron stainless steel mesh is fitted on the inlet side of the unit. The filters have been specially designed for backflushing in a way which enhances overall operational life.
BlueSonic is offered as turnkey project including 3D scanning of the engine room, prefabrication of the pipework, installation of the pipework at sea, followed by a short period of about 10 days in port for the final installation and commissioning work. Alternatively, Blue Sonic can be supplied separately for installation by third parties.
BlueSonic is supported by a world-wide network of service stations.
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
For more information please contact: [email protected]

Turbo Bilgewater Separators

The SKF Turbulo-MPB Bilge Water Separator with development dating back to 1925
The Turbulo-MPB Bilge Water Separator is the latest development of the Turbulo separator which dates back to 1925. With this experience combined with continuous development, the Turbulo-MPB Bilge Water Separator provides a highly reliable, trouble free way to comply with the latest MEPC regulations.
The Turbulo MPB Bilge Water Separator is a two-stage oily water separator that is suitable for use onboard any ship or offshore platform. It fulfils the 5 ppm criteria as well as the IMO 15 ppm requirements.
The sizes range from 0.25 m3/h to 10 m3/h.
As an option, we recommend fitting the Turbulo Sludge Buoy in the holding tank. With this simple mechanical device, it is possible to remove the oil which has separated out in the holding tank before it even enters the separator, thereby reducing maintenance and cleaning of the separator unit very considerably.
The first stage of the separator unit is a pressure system, with oleophilic coalescer inserts, that operates on a gravitational principle. Oily water is passed through the separator via a helical rotor pump and the separated oil is drained by means of automatic level control. There is a heating coil to address heavy fuel oil scenarios. The second stage features HycaSep (hydrocarbon separator) elements which coalesce the finest oil particles. An IMO certified monitor is included.
The unit operates fully automatically with continuous monitoring. The pump has run-dry protection. Maintenance is easy. There is no need to dismantle any pipes or fittings. The units are supported by a world-wide network of service stations.
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
For more information please contact: [email protected]

Simplex Fin Stabilisers

The Simplex Fin Stabiliser with anti-vortex tips and ultra high lift fin
Simplex fin stabilisers have been proven in many installations over many decades. They are robust and highly reliable. They have been subject to continuous development and represent the leading edge of this technology.
All retractable fin stabilisers have anti-vortex tips. The Ultra High Lift Fin is a special tail flap which increases roll reduction efficiency by up to 15% compared with conventional two-part fin stabilizers.
Depending on your requirements, you can select:
  • Standard retractable fin stablisers
  • Zero speed retractable fin stabilisers
  • Special stabiliser covers to reduce drag in way of the fin box.
  • Fixed fin stabilisers
  • Special Eco mode control software
  • Retrofits of updated control systems for existing stablisers
  • Rudder based roll stabilisation – see our information on steering gear.
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
For more information please contact: [email protected]

Simplex Rotary Vane Steering Gear

The Simplex rotary vane steering gear with fast response times and angles of up to 65 degrees
The Simplex rotary vane steering gear is a high-performance steering gear with very fast response times and angles up to 65 degrees or more on twin rudder systems with asymmetrical rudder angles.
Being relatively small in size, it is ideal for smaller vessels where space is an issue or where high performance is required. The steering gear can be used with any type of rudder.
Because of its very high speed of reaction, the steering gear is available for use on its own as a roll reduction system. By eliminating the need for fin stabilisers, this steering gear is particularly suitable for applications where the acoustic signal should be reduced.
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
For more information please contact: [email protected]

Becker Mewis Duct

The Becker Mewis Duct® positioned ahead of the propellor to straighten and accelerate the flow of water onto the propeller
The Becker Mewis Duct has proven its energy saving capabilities on many installations over more than the ten years. The Duct is positioned ahead of the propeller so that it can straighten and accelerate the flow of water onto the propeller, thereby producing a net forward thrust. At the same time the fins provide a pre-swirl which reduces losses in the propeller slipstream. The resultant increase in thrust at a given propulsive power makes savings of between 3 – 8% attainable depending on the individual hull / propeller interaction. Additional advantages include reduced cavitation and vibration.
The Becker Mewis Duct is equally suited to newbuildings and to retrofits. Savings are greatest for bulkers and tankers but multipurpose vessel can typically expect to save between 3 – 5%. Becker have also developed a special version of the Mewis Duct for container vessels and other fast vessels with operating speeds in excess of 18 knots. This version of the Mewis duct has a smaller nozzle with much lower drag and with fins which extend outwards beyond the nozzle. Saving 3-4% can be expected.
All Mewis ducts are designed to suit the hull shape of the individual vessel and are tank tested to prove the design before manufacture commences
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
For more information please contact: [email protected]

Becker Intelligent Monitoring System (BIMS)

Becker Intelligent Monitoring System with its simple interface
BIMS measures the ruder forces and interfaces with the vessel’s navigation systems as well as visualising the rudder lift on the bridge. This improves manoeuvrability but also prevents oversteering when the auto-pilot is in operation. The reduced rudder movements during auto-pilot operation (and also dynamic positioning) resulting energy savings of 1 – 1.5% depending on the type of operation as well as less wear and tear on the steering components.
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
For more information please contact: [email protected]

Becker Rudders

Becker twisted leading edge rudder
The name Becker is synonymous with high-performance rudders. The range includes
  • Flap rudders
  • Schilling rudders
  • Twisted leading edge rudders
  • Twisted trailing edge rudders
  • Rudder bulbs
  • Steering nozzles
Becker will optimise your manoeuvring system according to the specific design and operational requirements of
your vessel.
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
For more information please contact: [email protected]

24 hour service
Tel: +44 (0) 1264 860186
[email protected]

© Copyright 2021
Diesel and Marine Group

Terms and conditions, Privacy policy